adding support for lpc13uxx
This commit is contained in:
hathach
@@ -0,0 +1,144 @@
|
||||
/**************************************************************************/
|
||||
/*!
|
||||
@file board_ea4357.h
|
||||
@author hathach (tinyusb.org)
|
||||
|
||||
@section LICENSE
|
||||
|
||||
Software License Agreement (BSD License)
|
||||
|
||||
Copyright (c) 2013, hathach (tinyusb.org)
|
||||
All rights reserved.
|
||||
|
||||
Redistribution and use in source and binary forms, with or without
|
||||
modification, are permitted provided that the following conditions are met:
|
||||
1. Redistributions of source code must retain the above copyright
|
||||
notice, this list of conditions and the following disclaimer.
|
||||
2. Redistributions in binary form must reproduce the above copyright
|
||||
notice, this list of conditions and the following disclaimer in the
|
||||
documentation and/or other materials provided with the distribution.
|
||||
3. Neither the name of the copyright holders nor the
|
||||
names of its contributors may be used to endorse or promote products
|
||||
derived from this software without specific prior written permission.
|
||||
|
||||
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
|
||||
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
||||
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
|
||||
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
||||
INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
||||
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
|
||||
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
||||
INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
|
||||
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
|
||||
This file is part of the tinyusb stack.
|
||||
*/
|
||||
/**************************************************************************/
|
||||
|
||||
/** \file
|
||||
* \brief TBD
|
||||
*
|
||||
* \note TBD
|
||||
*/
|
||||
|
||||
/** \ingroup TBD
|
||||
* \defgroup TBD
|
||||
* \brief TBD
|
||||
*
|
||||
* @{
|
||||
*/
|
||||
|
||||
#ifndef _TUSB_BOARD_EA4357_H_
|
||||
#define _TUSB_BOARD_EA4357_H_
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
#include "LPC43xx.h"
|
||||
#include "lpc43xx_scu.h"
|
||||
#include "lpc43xx_cgu.h"
|
||||
#include "lpc43xx_gpio.h"
|
||||
#include "lpc43xx_uart.h"
|
||||
#include "lpc43xx_i2c.h"
|
||||
|
||||
|
||||
#include "oem_base_board/pca9532.h" // LEDs
|
||||
#include "oem_board/nand.h"
|
||||
|
||||
|
||||
//#define CFG_PRINTF_TARGET PRINTF_TARGET_SWO
|
||||
#define CFG_PRINTF_TARGET PRINTF_TARGET_UART // FIXME keil's cmsis rtx does not work with UART (work with SWO)
|
||||
|
||||
/*=========================================================================
|
||||
HARDWARE MAC ADDRESS
|
||||
-----------------------------------------------------------------------*/
|
||||
#define BOARD_MAC_ADDR0 0x00
|
||||
#define BOARD_MAC_ADDR1 0x10
|
||||
#define BOARD_MAC_ADDR2 0x20
|
||||
#define BOARD_MAC_ADDR3 0x30
|
||||
#define BOARD_MAC_ADDR4 0x40
|
||||
#define BOARD_MAC_ADDR5 0x50
|
||||
/*=========================================================================*/
|
||||
|
||||
/*=========================================================================
|
||||
EMAC CONFIGURATION
|
||||
-----------------------------------------------------------------------*/
|
||||
/* The PHY address connected the to MII/RMII */
|
||||
#define LPC_PHYDEF_PHYADDR 1 /**< The PHY address on the PHY device. */
|
||||
|
||||
/* Enable autonegotiation mode.
|
||||
* If this is enabled, the PHY will attempt to auto-negotiate the
|
||||
* best link mode if the PHY supports it. If this is not enabled,
|
||||
* the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
|
||||
* used to select the link mode. Note that auto-negotiation may
|
||||
* take a few seconds to complete.
|
||||
*/
|
||||
#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
|
||||
|
||||
/* Sets up the PHY interface to either full duplex operation or
|
||||
* half duplex operation if PHY_USE_AUTONEG is not enabled.
|
||||
*/
|
||||
#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
|
||||
|
||||
/* Sets up the PHY interface to either 100MBS operation or 10MBS
|
||||
* operation if PHY_USE_AUTONEG is not enabled.
|
||||
*/
|
||||
#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
|
||||
|
||||
/* Selects RMII or MII connection type in the EMAC peripheral */
|
||||
#define LPC_EMAC_RMII 1 /**< Use the RMII or MII driver variant */
|
||||
|
||||
/* Defines the number of descriptors used for RX */
|
||||
#define LPC_NUM_BUFF_RXDESCS 20
|
||||
|
||||
/* Defines the number of descriptors used for TX */
|
||||
#define LPC_NUM_BUFF_TXDESCS 20
|
||||
|
||||
/* Enables slow speed memory buffering
|
||||
* Enable this define if you expect to transfer packets directly
|
||||
* from SPI FLASH or any slower memory. This will add a check
|
||||
* before queueing up the transfer pbuf to make sure the packet
|
||||
* is not in slow memoey (defined by the LPC_SLOWMEM_ARRAY). If
|
||||
* the packet does exists in slow memory, a pbuf will be created
|
||||
* in the PBUF_RAM pool, copied to it, and sent from there.
|
||||
*/
|
||||
#define LPC_CHECK_SLOWMEM 0
|
||||
|
||||
/* Array of slow memory addresses for LPC_CHECK_SLOWMEM
|
||||
* Define the array - start and ending address - for the slow
|
||||
* memory regions in the system that need pbuf copies.
|
||||
*
|
||||
* Not defined since LPC_CHECK_SLOWMEM = 0.
|
||||
*/
|
||||
#define LPC_SLOWMEM_ARRAY
|
||||
/*=========================================================================*/
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* _TUSB_BOARD_EA4357_H_ */
|
||||
|
||||
/** @} */
|
||||
Reference in New Issue
Block a user